Showing 1–10 of 16 results

Out Of Stock

AEOTEC Micro Switch

The Aeotec Micro Switch is a low-cost Z-Wave appliance module specifically used to enable Z-Wave command and control ON/OFF for existing in-wall switches. It can also report immediate wattage consumption and energy usage over time.

 

The wireless module is powered from the mains supply and is a three-wire design which requires a neutral connection. In the event of a power failure, non-volatile memory retains all programmed information relating to the unit’s operating status.

DHS Garage Press Limit Switch

The DHS Garage Press Limit Switch is an industrial quality mechanical switch activated by the motion of garage doors, gates, windows etc.

The DHS Garage Press Limit Switch can be connected with any binary Z-Wave sensors to report the status of your garage door to your Z-Wave gateway.

DHS Garage Roller Limit Switch

The DHS Garage Roller Limit Switch is an industrial quality mechanical switch activated by the motion of garage doors, gates, windows etc.

The DHS Garage Roller Limit Switch can be connected with any binary Z-Wave sensors to report the status of your garage door to your Z-Wave gateway.

Note: A Z-Wave sensor is not included with this device.

FIBARO Z-Wave Double Switch InWall

The Fibaro Z-Wave Double Switch Controller (FGS-222) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.

The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.

The Fibaro Z-Wave Double Switch Controller (FGS-222) is a wireless controller which can control two circuits each with a maximum load of 1.5kW per circuit.

  • Control the ON-OFF function of two two independent lights or appliances remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling

FIBARO Z-Wave Single Switch InWall

The Fibaro Z-Wave Single Switch Controller is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.

The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.

The Fibaro Z-Wave Single Switch Controller is a wireless controller which can control appliances or lighting up to a maximum load of 2.5kW 10A.

  • Control the ON-OFF function of a circuit remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling

FIBARO Z Wave Double Switch 2

The Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.

The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.

The new Fibaro Z-Wave Double Switch 2 (FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.

  • Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus certification
  • Very accurate energy measurement +/- 1 % for power above 5W
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128

FIBARO Z Wave Single Switch 2

The Fibaro Z-Wave Single Switch 2 is a smart Z-Wave module capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.

The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.

The Fibaro Z-Wave Single Switch 2 is a wireless Z-Wave module which can control appliances or lighting up to a maximum load of 2.0kW.

  • Control the ON-OFF function of a circuit remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • control loads up to 2kW (8A)

GOAP Z-Wave Double Switch

The GOAP Double Switch is Z-Wave module for switching on or off one or two electrical devices (e.g. light, fan, etc …). The module can be controlled either through Z-wave network or through the wall switch manually.

This module is designed to be mounted  behind a traditional wall switch. Module measures power consumption of load and supports connection of digital temperature sensor. It is designed to act as repeater in order to improve range and stability of Z-Wave network.

Supported switches

Module supports mono-stable switches (push button) and bi-stable switches. The module is factory set to operate with bi-stable switches.

 

Features:

  • Compatible with any Z-Wave Controller.
  • Dimensions (W x H x D) 41,8 x 36,8 x 15,4mm
  • Power monitoring accuracy P=5-50W, +/-3W; P˃50W, +/-3%;
  • Digital temperature sensor range (sensor must be ordered separately) -50 ~ 125°C
  • Support for the connection of digital temperature sensor (optional part)
  • 2 binary inputs offer the option to connect additional devices such as sensors, switches/push buttons, etc.

DHS Z-Wave Switch PlugIn

The DHS Z-Wave Plug-In Switch is a smart switch with power measuring function which can be plugged into an Australian certified wall socket and used to turn home appliances ON and OFF.

  • Easy to use and DIY install
  • Completely wireless
  • Control ON/OFF function remotely by Z-Wave™ certified controllers / apps
  • Can be operated manually by the button on the device
  • Measure and report the power that is consumed through the socket (connected load)
  • Australian SAA certification
  • Configuration via Z-Wave parameters: Auto switch-off, Power reporting precision, Last knows status, and more

GOAP Z-Wave Single Switch

The GOAP Single Switch is Z-Wave module for switching on or off the electrical device (e.g. light, fan, etc …). The module can be controlled either through Z-wave network or through the wall switch manually.

This module is designed to be mounted  behind a traditional wall switch. Module measures power consumption of load and supports connection of digital temperature sensor. It is designed to act as repeater in order to improve range and stability of Z-Wave network.

Supported switches

Module supports mono-stable switches (push button) and bi-stable switches. The module is factory set to operate with bi-stable switches.

 

Features:

  • Compatible with any Z-Wave Controller.
  • Dimensions (W x H x D) 41,8 x 36,8 x 15,4mm
  • Power monitoring accuracy P=5-50W, +/-3W; P˃50W, +/-3%;
  • Digital temperature sensor range (sensor must be ordered separately) -50 ~ 125°C
  • Support for the connection of digital temperature sensor (optional part)
  • 2 binary inputs offer the option to connect additional devices such as sensors, switches/push buttons, etc,